- whatsapp +51955515985
- support@ecuforcetruck.com
- 24/7 Customer Support
Menu
Shop
Account
Subtotal: $0.00
No products in the cart.
Circuit Description
The aftertreatment particulate matter sensor is a smart device and communicates with the engine control module (ECM) via the J1939 data link. The aftertreatment particulate matter sensor performs internal diagnostics and reports malfunctions back to the primary ECM using the J1939 data link. The particulate matter sensor is permanently attached to the particulate matter control module. They are serviced as a single component and can not be replaced individually. The aftertreatment particulate matter sensor is used to measure the soot emissions at the outlet of the aftertreatment system.
Component Location
The aftertreatment particulate matter sensor location can vary depending on engine application. It is usually located in the exhaust system at the outlet of the selective catalytic reduction (SCR) catalyst.
Conditions for Running the Diagnostics
This diagnostic runs continuously when the engine is running.
Conditions for Setting the Fault Codes
An internal circuit error was detected in the aftertreatment particulate sensor assembly
Action Taken When the Fault Code is Active
The ECM illuminates the amber CHECK ENGINE lamp and/or Malfunction Indicator Lamp (MIL) after the diagnostic fails on two consecutive trips.
Conditions for Clearing the Fault Code
To validate the repair, start the engine and let it idle for 1 minute.
The ECM will turn off the amber CHECK ENGINE lamp immediately after the diagnostic runs and passes.
The fault code status displayed by INSITE™ electronic service tool will change to INACTIVE immediately after the diagnostic runs and passes.
For On-Board Diagnostics (OBD) engines, the ECM will extinguish the Malfunction Indicator Lamp (MIL) after three consecutive trips where the diagnostic runs and passes.
The Reset All Faults command in INSITE™ electronic service tool can be used to clear active and inactive faults, as well as extinguish the MIL for OBD applications.
Shop Talk
Possible causes for this fault include:
Malfunctioning aftertreatment particulate matter sensor
Possible Cause:
1) ECM calibration
Related
Categories Cumminz, DTC TRUCKS, Tags , 1, 2018, 3, 4143, 5835, Above, Aftertreatment, Circuit-, CM2450, Code, Cummins, Fault, FMI, High, Newer, Normal, or, Particulate, PID, Sensor, Shorted, Source, SPN, to, Voltage, X124B, X15
Wiring Diagrams
Component Locators
- Perkins EST 2016C Electronic Service Tool
Perkins$50.00
Rated 0 out of 5
- Caterpillar CAT ET 2021B Electronic Technician + Factory Password (1PC)
CAT$75.00
Rated 0 out of 5
- Perkins EST 2021B v1.0 Active License + FPKG ( 1 PC )
CAT$75.00
Rated 0 out of 5
JPRO$94.00
Rated 0 out of 5
- AGCO EDT 2023.10 Electronic Diagnostic Tool 1.125
AGCO$120.00
Rated 0 out of 5
- NEXIQ eTechnician 2.1.7657.26963 + Patch 2020
Allison$60.00
Rated 0 out of 5
Detroit$30.00
Rated 0 out of 5
- Meritor WABCO Toolbox 12.12 Software
Trucks software$40.00
Rated 0 out of 5
- DOWNLOAD VOLVO MATRIS 2.3.3
Trucks software$60.00
Rated 0 out of 5
- Isuzu IDSS 2021 Diagnostic Software
ISUZU$100.00
Rated 0 out of 5
- Detroit Diesel Drumroll Engineering 7.06 DDDE v7.06
Detroit$20.00
Rated 0 out of 5
- Detroit BackDoor Password Generator V1 V2
Detroit$30.00
Rated 0 out of 5
- Bendix 6.16 ACom Diagnostics ( bendix software trucks )
Bendix$35.00
Rated 0 out of 5
- Meritor Wabco Tool Box 12.9.1
Trucks software$35.00
Rated 0 out of 5
- Allison DOC 2019 PC software + GEN5 2019 truck
Allison$40.00
Rated 0 out of 5
- Freightliner ServiceLink 4.9.6
Freightliner$30.00
Rated 0 out of 5
- Allison DOC 2021 V2 (1PC)
Allison$67.00
Rated 0 out of 5
- JOHN DEERE SERVICE ADVISOR 5.3.225 DATABASE AG + CF ENGLISH 2023
John Deere$250.00
Rated 0 out of 5
- Diamond Logic Builder DLB 2018
Navistar$40.00
Rated 0 out of 5
- JPRO Diagnostic Software Download 2024
JPRO$100.00
Rated 0 out of 5
Related products
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
- PACCAR PX-9 CM2350 (2013-17) Fault Code:3634 PID: SPN:5484 FMI:4 Engine Fan Clutch 2 Control Circuit – Voltage Below Normal or Shorted to Low Source
DTC TRUCKS
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
- Bendix ABS EC-30 Fault Code: SID 251 FMI 3
Bendix ABS
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
- SERVICE MANUAL MACK E7
MACK$27.00
Rated 0 out of 5
- SERVICE MANUAL MACK V-MAC IV (2010 Emissions)
MACK$40.00
Rated 0 out of 5
- SERVICE MANUAL Input and Output Configurations Allison Transmission
Allison$21.00
Rated 0 out of 5
- SERVICE MANUAL HINO FD.FE.FF.SG 2009
HINO$34.00
Rated 0 out of 5
INTERNATIONAL ENGINES$17.00
Rated 0 out of 5
- SERVICE MANUAL BOBCAT 442 sms
BOBCAT$50.00
Rated 0 out of 5
- SERVICE MANUAL BOBCAT 316 SMS
BOBCAT$45.00
Rated 0 out of 5
- SERVICE MANUAL BOBCAT 553 sms
BOBCAT$60.00
Rated 0 out of 5
- SERVICE MANUAL DETROIT Earings – Technicians Guide
DETROIT$18.00
Rated 0 out of 5
- SERVICE MANUAL BOBCAT 100 sms
BOBCAT$54.00
Rated 0 out of 5